The layers /Reblog Lottery DUO BONUS !

A bit over 2 weeks ago I posted about some failed casting experiments and mentioned I got a new smaller diameter nozzle for my 3d printers, link to that post here

Well in this post I got deeper into this topic.

Usually printers come with a 0.4mm diameter nozzle(the hole where the plastic comes out)
Different nozzles sizes are good for different things a thicker nozzle will be able to lay down material faster finishing the prints faster however you get worse detail as the bigger layers and the width of the layer line can catch less details.

A thinner nozzle has the opposite effect it lays down less material and takes more time but you can get more detail.

Now this model is not a great example as the details are not too crazy but it's a fast print so it's a good bench mark.

We start with the standard 0.4 nozzle and 0.2mm layer height right below you can see how it looks like, notice the lines yep not the nicest, this took about 15 minutes to print.

Then I swapped the nozzle with a 0.2 and started with a 0.1 layer height, as you can see bellow it's a lot harder to see the lines and it would potentially show more details in a more complicated model.

Then I tried a 0.05 layer height with the same 0.2 nozzle, in this one it's even harder to see the layer lines and it's a lot more smoother and has room for even more details, however it didn't come out great, that is a matter of messing with the settings on the printer since it's a stretch from the standard 0.4 nozzle and the usual layer height range of 0.15-0.2

Since then I got some more nozzle sizes as well as some extras because they dont' last forever they get worn down over time and sometimes there can be a clog that can't be cleared easily.

along with the standard 0.4 and this new more fine 0.2 nozzle I also got a 0.6 0.8 and a 1.0 these bigger nozzles will give me faster prints but at the cost of details, they all have their uses.

There is a special print mode called vase mode and in that mode the nozzle goes around in a spiral and is only one wall thick this is not great for every model but it allows you to make some very fast prints (usually useful for making vases hence the name) this however means that the part is rather flimsy, however if using a bigger nozzle the wall will be thicker and hence more strong.

---

Reblog lottery

We got 34 participants for our reblog lottery this time around.

@blessed-20 @blitzzzz @chaosmagic23 @cup-bearer @daniasi @duckmotor @ecencypoints @ekads @ferod23 @fonestreet @henruc @hjrrodriguez @jenam @jhonnygo @jorgebgt @khantaimur @kungfukid @ladymisa @miriammarga @mxm0unite @necho41 @nkemakonam89 @olaf.gui @pepetoken @rebe.torres12 @servelle @stekene @sylmarill @tengolotodo.leo @trautenberk @vaynard86 @vrezyy @ydm6669 and @yova

and the winner this time around is....

Looks like we got a dud, better luck next time !

@ekads! Congratulations enjoy your 10% profit share on this post, 0.33 DUO tokens, 5 HBI units more about HBI units here

The reblog lottery continues so be sure to reblog this post to qualify, for a minimum 10% profit share, 0.33 DUO token and 5 HBI units (bonus wheel) on my next post

This is all done automatically and I apply the winner to be a beneficiary for the post.

Only reblogs before tomorrow 8pm Eastern Standard Time qualify for the lottery.

---

I am a financial advisor ! If you can't take personal responsibility for you investing, I hate to brake it to ya, but you ain't nothing but a sucka, you supposed to lose your shit.

@bitcoinman's bits of wisdom

• Invest only what you can afford to lose and be mindful of the potential risks.
• Unless you can accept delivery stay away from futures and stick to physical.
• Leverage is a great tool for losing money fast.
• Numismatics for the lows stick to smart stacking baby.
• Be cautious of new schemes in crypto, like ICOs, DeFi, and NFTs, do your research before investing.

---

BUY/SELL PRECIOUS METALS WITH HBD + PRECIOUS METALS TOOLS AND ACCESSORIES

---

Buy DUO and stake to receive Hive dividends, tip others, have your posts curated and grow Hive!
Learn more about DUO here
https://tribaldex.com/trade/DUO
https://hive-engine.com/trade/DUO

You can find out more about the #silvergoldstackers community in this post here

HOC Hive Onboarding Committee discord link here

---

Weekly Post Schedule

---

Profit share

10% of this post earnings go to @ekads for being our reblog lottery winner.

---

That's it for today's post thanks for stopping by your support is truly appreciated.

Posted Using InLeo Alpha